General specifications
Signal type    Analog input
Functional safety related parameters
Safety Integrity Level (SIL)    SIL 2
Supply
Connection    terminals 14+, 15- or power feed module/Power Rail
Rated voltage    20 ... 30 V DC
Ripple    within the supply tolerance
Power dissipation    ≤ 0.98 W
Power consumption    max. 0.98 W
Interface
Programming interface    programming socket
Input
Connection side    field side
Connection    terminals 1, 2, 3, 4
RTD    type Pt10, Pt50, Pt100, Pt500, Pt1000 (EN 60751: 1995)
type Pt10GOST, Pt50GOST, Pt100GOST, Pt500GOST, Pt1000GOST (6651-94)
type Cu10, Cu50, Cu100 (P50353-92)
type Ni100 (DIN 43760)
Measuring current    approx. 200 µA with RTD
Types of measuring    2-, 3-, 4-wire connection
Lead resistance    max. 50 Ω per line
Measurement loop monitoring    sensor breakage, sensor short-circuit
Thermocouples    type B, E, J, K, N, R, S, T (IEC 584-1: 1995)
type L (DIN 43710: 1985)
type TXK, TXKH, TXA (P8.585-2001)
Cold junction compensation    external and internal
Measurement loop monitoring    sensor breakage
Potentiometer    0 ... 20 kΩ (2-wire connection), 0.8 ... 20 kΩ (3-wire connection)
Voltage    selectable within the range -100 ... 100 mV
Input resistance    ≥ 1 MΩ (-100 ... 100 mV)
Output
Connection side    control side
Connection    output I: terminal 7: source (-), sink (+), terminal 8: source (+), terminal 9: sink(-)
Output    Analog current output
Current range    0 ... 20 mA or 4 ... 20 mA
Fault signal    downscale 0 or 2 mA, upscale 21.5 mA (acc. NAMUR NE43)
Source    load 0 ... 550 Ω
open-circuit voltage ≤ 18 V
Sink    Voltage across terminals 5 ... 30 V. If the current is supplied from a source > 16.5 V,
series resistance of ≥ (V - 16.5)/0.0215 Ω is needed, where V is the source voltage.
The maximum value of the resistance is (V - 5)/0.0215 Ω.
Transfer characteristics
Deviation    
After calibration    Pt100: ± (0.06 % of measurement value in K + 0.1 % of span + 0.1 K (4-wire connection))
thermocouple: ± (0.05 % of measurement value in °C + 0.1 % of span + 1 K (1.2 K for types R and S)) , includes ± 0.8 K fault of the cold junction compensation (CJC)
mV: ± (50 µV + 0.1 % of span)
potentiometer: ± (0.05 % of full scale + 0.1 % of span, (excludes faults due to lead resistance))
Influence of ambient temperature    Pt100: ± (0.0015 % of measurement value in K + 0.006 % of span)/K ΔTamb*)
thermocouple: ± (0.02 K + 0.005 % of measurement value in °C + 0.006 % of span)/K ΔTamb*)), influence of cold junction compensation (CJC) included
mV: ± (0.01 % of measurement value + 0.006 % of span)/K ΔTamb*)
potentiometer: ± 0.006 % of span/K ΔTamb*)
*) ΔTamb = ambient temperature change referenced to 23 °C (296 K)
Influence of supply voltage    < 0.01 % of span
Influence of load    ≤ 0.001 % of output value per 100 Ω
Reaction time    worst case value (sensor breakage and/or sensor short circuit detection enabled)
mV: 1 s, thermocouples with CJC: 1.1 s, thermocouples with fixed reference temperature: 1.1 s, 3- or 4-wire RTD: 920 ms, 2-wire RTD: 800 ms, Potentiometer: 2.05 s